mirror of
https://github.com/cimryan/teslausb.git
synced 2026-02-28 20:20:32 +00:00
92 lines
4.5 KiB
Markdown
92 lines
4.5 KiB
Markdown
# Introduction
|
|
|
|
This guide will show you how to install and configure [rclone4pi](https://github.com/pageauc/rclone4pi/wiki) (based off [rclone](https://rclone.org/)) to archive your saved TeslaCam footage on one of a number of different remote storage services including Google Drive, S3 and Dropbox.
|
|
|
|
You must perform these steps **after** getting a shell on the Pi and **before** running the `setup-teslacam` script on the Pi.
|
|
|
|
**Make sure to run all commands in these instructions in a single command shell as root. When you return to the [Main Instructions](/README.md) continue running the commands there in this same shell.** This is necessary because:
|
|
* The `archiveloop` script runs as root and the rclone config is bound to the user running the config.
|
|
* These commands define environment variables that the main setup scripts need.
|
|
|
|
# Quick guide
|
|
These instructions will speed you through the process with good defaults. If you encounter an error, or you want to use a different config name than `gdrive` or a different folder name than `TeslaCam`, follow the detailed instuctions, below.
|
|
|
|
1. Run these commands. Specify the config name `gdrive` when prompted for the config name.
|
|
```
|
|
sudo -i
|
|
curl -L https://raw.github.com/pageauc/rclone4pi/master/rclone-install.sh | bash
|
|
rclone config
|
|
```
|
|
1. Run these commands:
|
|
```
|
|
export ARCHIVE_SYSTEM=rclone
|
|
export RCLONE_DRIVE=gdrive
|
|
export RCLONE_PATH=TeslaCam
|
|
|
|
rclone mkdir "$RCLONE_DRIVE:$RCLONE_PATH"
|
|
rclone lsd "$RCLONE_DRIVE":
|
|
```
|
|
1. If you didn't encounter any error messages and you see the `TeslaCam` directory listed return to the [Main Instructions](../README.md).
|
|
|
|
# Detailed instructions
|
|
## Step 1: Install rclone4pi
|
|
1. Run this command to enter a command shell for the root user.
|
|
```
|
|
sudo -i
|
|
```
|
|
2. Run the following command to install rclone4pi:
|
|
```
|
|
curl -L https://raw.github.com/pageauc/rclone4pi/master/rclone-install.sh | bash
|
|
```
|
|
Alternatively, you can install rclone4pi manually by following these [instructions] (https://github.com/pageauc/rclone4pi/wiki#manual-install).
|
|
|
|
# Step 2: Configure the archive
|
|
1. Run this command to configure an archive:
|
|
```
|
|
rclone config
|
|
```
|
|
This will launch an interactive setup with a series of questions. It is recommended that you look at the documentation for your storage system by going to [rclone](https://rclone.org/) and selecting your storage system from the pull down menu at the stop.
|
|
|
|
It has been confirmed that this process works with Google Drive using these [instructions](https://rclone.org/drive/). If you are using another storage system, please feel encouraged to create an "Issue" describing your challenges and/or your success.
|
|
|
|
If you are using Google Drive it is important to set the correct [scope](https://rclone.org/drive/#scopes). Carefully read the documentation on [scopes on rclone](https://rclone.org/drive/#scopes) as well as [Google Drive](https://developers.google.com/drive/api/v3/about-auth). The `drive.file` scope is recommended.
|
|
|
|
**Important:** During the `rclone config` process you will sepcify a name for the configuration. The rest of the document will assume the use of the name `gdrive`; replace this with your chosen configuration name.
|
|
|
|
1. Run this command:
|
|
```
|
|
export RCLONE_DRIVE="gdrive"
|
|
```
|
|
# Step 3: Verify and create storage directory
|
|
|
|
1. Run the following command to see the name of the remote drive you just created.
|
|
```
|
|
rclone listremotes
|
|
```
|
|
If you don't see the name there, something went wrong. Go back through the `rclone config` process.
|
|
1. Run this command:
|
|
```
|
|
rclone lsd "$RCLONE_DRIVE":
|
|
```
|
|
You should not see any files listed. If you do then you did not set your scope correctly during the `rclone config` process.
|
|
1. Choose the name of a folder to hold the archived clips. These instructions will assume you chose the name `TeslaCam`. Substitute the name you chose for this name. Run this command:
|
|
```
|
|
export RCLONE_PATH="TeslaCam"
|
|
```
|
|
1. Run the following command to create a folder which will hold the archived clips.
|
|
```
|
|
rclone mkdir "$RCLONE_DRIVE:TeslaCam"
|
|
```
|
|
1. Run this command again:
|
|
```
|
|
rclone lsd "$RCLONE_DRIVE":
|
|
```
|
|
Confirm that the directory `TeslaCam` is present. If not, start over.
|
|
|
|
# Step 4: Exports
|
|
Run this command to cause the setup processes which you'll resume in the main instructions to use rclone4pi:
|
|
```
|
|
export ARCHIVE_SYSTEM=rclone
|
|
```
|
|
Now return to the section "Set up the USB storage functionality" in the [main instructions](../README.md).
|